Essential Plumber Insights for Bathtub Installation
Essential Plumber Insights for Bathtub Installation
Blog Article
We have discovered the article pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the internet and concluded it made sense to write about it with you in this article.
Mounting a bath tub isn't precisely rocket science, yet it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably tough project. If the old bathtub is easily accessible, the job can relocate rapidly; if you need to open up a wall surface to remove the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to leave the old tub as well as set in the new one. Make sure you have certified yourself for the job as well as are comfortable trying it. As opposed to working with a service provider to take over a halfway-completed project, it is far better to take into consideration employing one before you begin. Opportunities are you may need an expert plumber to make tube connections.
This short article will assist you set up a new bath tub in your restroom if you have already bought a brand-new bathtub as well as don't need to change the plan of your previous water system pipes.
Your tools and also material list need to make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any water remaining in the system. The process of removing the existing taps can be quite troublesome as a result of the restricted access that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the staying water that will come from the pipes. Once the supply pipes have been removed, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any old sealing substance.
Before proceeding to fit the brand-new taps, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the mounting opening in the bath/basin making sure that the washers remain in place in between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet connectors. The former type must be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bathtub
Using the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are practical in uniformly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bath tub till the level reads degree.
To set up taps, fit all-time low of the outermost flexible faucet port to the appropriate supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water supply and examine all joints and also brand-new pipework for leakages and tighten them if necessary. Load the bathtub as well as additionally examine the overflow outlet as well as the typical outlet for leakages.
Ultimately, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the tub must wait till the bathtub has been used a minimum of when as this will certainly resolve it into its final setting.
Getting ready for the Installation
Firstly, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps unit to avoid strain on the bathtub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final setting.
Tiling Around the Bath tub
In the location where the bathroom meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall between the bathroom and the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes and also cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can break rather very early if you do not take into consideration this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily available on the marketplace. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I hope you enjoyed reading our excerpt on Tools You Need to Install a New Bathtub . Many thanks for spending some time to read our post. If you liked our blog post if you please remember to pass it around. I value reading our article about How to Install a Bathtub.
Immediate response? Call. Report this page